Skip to main content
BerneCommercial
24/7 commercial dispatchSame-day serviceLicensed & InsuredParts warranty up to 10 years
Blog/Commercial Laundry

Commercial Dryer Not Heating? What to Check on Laundromat and Hotel Dryers

Why a commercial gas or electric dryer tumbles but stays cold: lint and exhaust airflow, the airflow (sail) switch, manual-reset high limits, ignition and gas valve faults, gas pressure and heating elements. What staff can check safely and when to call.

·7 min read
Commercial service call: $89Same-day dispatch

A commercial dryer that tumbles but blows cold air costs you twice: the load comes out wet and someone runs it again. In a laundromat the customer wants a refund; in a hotel, housekeeping falls behind on linens. Often the burner or the element is fine. The dryer refuses to heat because one of its safety checks failed, and the first ones to suspect have to do with air.

1. Start with lint and exhaust airflow

Commercial tumble dryers move a lot of air, and most will not light the burner, or will shut it off, when that air can't get out. A lint screen packed after a few loads, a lint compartment nobody emptied, a crushed transition duct behind the machine or an exhaust run with too many elbows will all cut airflow.

Clean the lint screen and the lint compartment, then look at the exhaust where it leaves the building. On long runs, a backdraft damper stuck shut or an outside hood packed with lint is a frequent find. Each model's installation manual sets the maximum duct length and elbow count, plus the makeup air the room needs. A dryer pulling against a sealed laundry room runs hot and trips.

Lint around the burner is a fire risk as well, so this check pays off even on a dryer that still heats.

2. The airflow (sail) switch

Many commercial dryers prove airflow before they allow heat. A light vane, often called a sail, sits in the airstream and closes a switch when enough air moves past it. Until that switch closes, the control won't open the gas valve or power the elements.

A restricted duct keeps the sail from moving. So does a sail bent out of shape or stuck with lint, and switch contacts can burn too. If the exhaust is clear and the dryer still won't heat, the airflow switch is the next suspect, and a tech confirms it with a meter while the dryer runs so the part isn't replaced on a guess.

3. High limits and thermal cutoffs

One overheat, usually from a lint problem, can trip a high-limit thermostat at the burner or in the exhaust path. On many commercial models that thermostat is a manual-reset type. It stays open until someone presses the reset button, so the dryer keeps tumbling cold even after the lint is gone.

A reset is not a repair. If the high limit trips again within a few days, something is still choking the airflow or the cycling thermostat is letting the drum run too hot, and a tech should find it before it turns into a fire.

4. Ignition and the gas valve

On a gas dryer that passes the airflow and high-limit checks, watch the burner at the start of a heat cycle through the view port, if your model has one. Depending on the model, the burner lights from a hot-surface igniter (a glow bar) or from a direct-spark ignition module that sparks at an electrode. A flame sensor then confirms the flame is there.

What you see narrows it down. No glow and no spark points to the ignition module and its power, or to the airflow and high-limit circuit ahead of it. Glow or spark with no flame points to the gas supply or the gas valve. A flame that lights and drops out after a few seconds is usually flame sensing, often a dirty or misaligned sensor or a poor ground. A flame that holds while loads still dry slowly sends you back to gas pressure and exhaust.

Single-pocket coin dryers built around a residential-style gas valve have one more classic failure. The valve coils work when cold and quit once warm, so the dryer heats for a few minutes and then stops.

5. Gas supply and pressure

If every dryer in a row heats weakly, or the machines at the end of the gas line go cold only when the whole bank is running, look at the supply. An undersized gas line or a regulator that can't keep up drops pressure under full load. A qualified tech checks each dryer's manifold pressure with a manometer against the rating plate.

If you smell gas, leave the dryers as they are and don't flip any switch. Get everyone out of the room and call your gas utility from outside.

6. Electric dryers: elements and contactors

Electric commercial dryers heat with element banks switched by contactors or relays. An open element or a contactor with burned contacts leaves the drum cold while the motor keeps turning. These are meter checks done with the power locked out. On three-phase machines the tech also reads the voltage on each leg, since a lost leg can kill part of the heat.

7. When the real problem is the washer

Some no-heat calls turn out to be drying-time complaints. A washer that no longer extracts well sends out loads holding too much water, and the dryer gets the blame. If drying times crept up on every dryer at once, check the washers' final spin and the shared exhaust before anyone orders dryer parts. Our commercial washer repair techs look at both sides on the same visit.

Same-day commercial laundry service

Berne Commercial Repair services commercial dryers in laundromats, hotels, condo buildings and multi-family laundry rooms across Miami-Dade, Broward and Palm Beach, including Speed Queen, Huebsch, UniMac, Maytag Commercial and Continental Girbau. The $89 commercial service call is free when you approve the repair. Book through our commercial dryer repair page or call (754) 345-4515. Whole laundry rooms, card systems included, are covered on the commercial laundry repair page, and everything else we fix is listed under commercial repair services.

Need a commercial tech on site?

$89 commercial service call, free with the approved repair. Same-day dispatch across South Florida.

Call (754) 345-4515Request Service