Skip to main content
BerneCommercial
24/7 commercial dispatchSame-day serviceLicensed & InsuredParts warranty up to 10 years
Blog/Restaurant Equipment

Restaurant Equipment Repair Cost in South Florida: 2026 Prices by Equipment

What restaurant equipment repairs cost in Miami-Dade, Broward and Palm Beach in 2026, from walk-ins and ice machines to fryers, ovens and dish machines, with figures from our own service tickets and the things that push a bill up.

·8 min read
Commercial service call: $89Same-day dispatch

Almost every first call from a restaurant gets to the same question within a minute: what is this going to cost me? It depends on the part, but the spread is narrower than most owners expect. On our tickets in Miami-Dade, Broward and Palm Beach, most kitchen repairs land between $80 and $1,200 for parts and labor. The big numbers come from a short list of jobs, mostly refrigerant leaks, dead compressors and combi steam generators. Below are the 2026 ranges by equipment, what goes into the bill, and the point where fixing a unit stops making sense.

What goes into a repair bill

Every visit starts with the $89 commercial service call, which covers the trip and the diagnosis. It is waived when you approve the repair, so you only pay it if you decide not to fix the unit. Before any work starts, the technician gives you a written price for parts and labor.

Two things can add to that. An emergency visit after 7 PM carries a $150 dispatch fee for kitchens without a service agreement, and that fee is also waived when you approve the repair. Special-order or OEM-only parts can need a deposit before we order them. There is no separate travel charge.

Walk-ins

On a walk-in, most of the calls start at the door or the evaporator. A worn gasket, a torn sweep, a hinge cam or a dead frame heater runs $150 to $450. An evaporator fan motor runs $200 to $450. A defrost failure (the timer, a heater or the termination thermostat) runs $250 to $700, and it usually shows up as ice on the coil and a box that creeps up overnight.

A refrigerant leak is the first expensive one: $400 to $1,200 for the leak repair and recharge, with the refrigerant itself billed at $90 to $150 a pound. The top of the range is the condensing unit. When the compressor dies on a system older than ten years, a new condensing unit costs $2,500 to $4,800. That still beats a new walk-in, since the insulated panels often last for decades.

Doors cause more of these calls than people expect, and our guide to a walk-in door that won't close or seal has the checks you can do first. Visits are booked through walk-in cooler repair.

Reach-ins and the bar

Reach-ins and prep tables cost less to fix. A gasket that has gone flat, or a thermostat or controller that drifts, runs $80 to $380. A condenser fan motor eaten by salt air runs $120 to $240; near the coast it is the failure we replace most often. A compressor that short-cycles because of a tired start relay or a fouled condenser runs $120 to $480, and a controller showing a fault code runs $120 to $420.

Back-bar coolers and kegerators sit a little higher. When every tap pours foam, the cause is a warm trunk line, low gas pressure or a temperature fault, and the fix runs $160 to $520. A beer cooler that never gets down to 34-38°F runs $220 to $900, depending on whether the trouble is a dirty condenser or the compressor.

Ice machines

Most ice machine repairs are small. No ice or thin cubes usually points to the water inlet valve or scale restricting flow, $90 to $260. A machine that runs but never drops a harvest needs a harvest sensor, $80 to $180. When production falls off in July, look at a dirty condenser or a corroded fan motor, $120 to $300. Ice that tastes or smells off calls for a sanitation cycle and a new filter, $180 to $340.

Two jobs cost more. Auger bearings on nugget and flake machines run $300 to $900, and the machine should be shut off as soon as it starts grinding. A dead compressor on a machine past ten years runs $800 to $1,400; read ice machine: repair or replace? before you approve that one. Service is booked through commercial ice machine repair.

The hot line

Hot-line repairs are mostly parts that wear out. On a fryer, a pilot that won't stay lit is a thermocouple or thermopile at $80 to $160, and a temperature probe that drops the fryer to standby mid-rush runs $90 to $160. Oil that overheats points to the thermostat or a stuck high-limit, $120 to $300. Ignition modules and combination gas valves run $180 to $380, and a Frymaster filter pump in lockout $260 to $520. More on the fryer side at fryer repair.

Range burners that won't light or burn weak come to $140 to $400. Low flame across the whole range is often gas pressure, which a tech sets with a manometer for $80 to $280. An old range with several burner sections failing at once may need a full burner rebuild at $850 to $1,200.

Ovens that won't ignite or heat need an ignition module, a gas valve or an element, $180 to $480. Uneven baking from a drifting thermostat or a worn blower runs $150 to $450. Combis cost more because of the water side. A combi that stops making steam runs $300 to $1,200, a fault code $200 to $700, and a dead steam generator on a boiler combi past ten years $3,000 to $5,000. A deck pizza oven that won't reach 500-700°F runs $180 to $900.

Dish machines

A high-temp dish machine that can't reach the 180°F sanitizing rinse almost always has a scaled or failed booster element or contactor, $180 to $620. Weak wash pressure from worn wash-arm bearings or a tired pump runs $90 to $480. A chemical pump that stopped dosing is $60 to $180, and door springs, gaskets and drain valves run $90 to $245.

When the booster dies on an old machine, the numbers change. An installed replacement dish machine runs $3,800 to $9,400, so a booster repair on a machine with years left in it is still the cheaper road. Booking is on commercial dishwasher repair.

Why one bill lands at the top of the range

The same symptom can cost the low number or the high one. Access is the usual reason. A condensing unit on a roof, a reach-in built into the cook line or a high-rise kitchen where the tech needs a freight elevator and a building escort all add labor. Then there is the part. A universal thermocouple costs little, while an OEM control board for a combi has to be ordered.

Age adds to it. On a 12-year-old unit the tech often finds a second worn part next to the failed one, and you decide whether to replace both on the same visit. And in South Florida there is the water. Scale builds on everything that heats it, so a booster or steam generator repair often comes with a descale.

After-hours work adds the $150 dispatch fee for kitchens without an agreement. Kitchens with a service agreement follow the rates written into it, and clients on a preventive maintenance plan are dispatched ahead of non-contract calls.

When a repair isn't worth it

We go by the 50% rule. If one repair costs more than about half the price of a comparable new unit, and the unit is near the end of its normal life, replacement usually wins. A $120 start relay on a four-year-old reach-in is an easy yes. A dead compressor on a 13-year-old reach-in usually isn't worth fixing.

Walk-ins are the exception, because the box outlives the machine on top of it; see why the 50% rule is wrong for walk-ins. Lifespans by equipment type are in how long commercial kitchen equipment lasts, and the calculator in our commercial kitchen repair cost guide runs the math on your own numbers.

Getting a price

Call (754) 345-4515 or book through our restaurant equipment repair page. Have the brand, model and serial number ready (a photo of the data plate works), and tell the dispatcher what the unit is doing and since when. The technician gives you a written quote on site, and nothing is done until you approve it.

Need a commercial tech on site?

$89 commercial service call, free with the approved repair. Same-day dispatch across South Florida.

Call (754) 345-4515Request Service